Iron-based chromium-manganese alloys with an increased range of tribological properties
Keywords:
chromium-manganese alloys, chemical composition, phase composition, thermal analysis, crystallization, wear resistance, heat treatment, structure, alloying, operational stabilitySynopsis
In this work, the rational compositions of the chemical composition of established and substantiated chromium-manganese alloys in the following ranges were: С = 2.6–3.0 %; Cr = 10.0–20.0 %; Mn = 10.0–15.0 %; Ni = 0.5–1.7 %; Si ≤ 1.3 %; V ≤ 0.3 %; Cu ≤ 0.3 %.
It has been determined that an additional increase in the complex of properties of chromium-manganese alloys can be achieved by the additional introduction of molybdenum, titanium, barium and calcium in small amounts.
The peculiarities of the formation of the structure, phase composition and properties of the investigated chromium-manganese alloys in the cast state were. The change in the temperature intervals of the beginning and end of melting/crystallisation of alloys with different alloying systems was determined by thermal analysis. A comparative analysis of the melting/crystallisation temperature intervals revealed that the developed chromium-manganese alloys are characterised by lower energy consumption of the production process, and, therefore, are more technologically advanced in terms of achieving the required superheat temperature, subsequent casting into moulds and crystallisation.
According to the results of comparative tests for friction wear (temperature up to 950 °C, load 500 N) and abrasive wear of chromium-manganese alloys with traditional analogue alloys in the cast state, it was found that the experimental material containing 3.10 % C 13.10 % Cr; 15.75 % Mn; 1.15 % Ni; 0.90 % Si; 0.25 % V and 0.15 % Cu, has higher wear resistance in contrast to high-chromium cast iron 300Х32Н3ФЛ and alloy chromium-nickel "nikorin" (36.0–38.0 % Cr; 57.0–59.0 % Ni).
The results of the study indicate that further development of effective heat treatment regimes for the proposed chromium-manganese alloys will increase the operational stability of the piercing mandrels of pipe rolling mills while reducing the material costs of their manufacture. When developing heat treatment regimes, special attention for chromium-manganese alloys, should be paid to obtaining metastable structures that are prone to decomposition and self-reinforcement during operation of finished products.
References
Rozhkova, Ye. V., & Vatkovskaya, I. Ye. (1985). Prokalivaemost iznosostoikikh chugunov. Liteinoe proizvodstvo, *1*, 33–35.
Stepina, A. I., Stupitskii, A. M., & Kleis, I. R. (1977). Vliyanie strukturi na iznosostoikost chugunov. Liteinoe proizvodstvo, *9*, 26–36.
Romanov, O. M., Rozhkova, Ye. V., Kozlov, L. Ya., & Shveikhman, A. O. (1981). Iznosostoikie lopatki drobemetnikh apparatov. Liteinoe proizvodstvo, *6*, 26–30.
Leshchenko, A. D., Kutuzov, A. D., & Lunev, V. V. (1988). Sostav khromistogo chuguna s zadannimi svoistvami. Liteinoe proizvodstvo, *6*, 8–12.
Timofeeva, L. A., Timofeev, S. S., Dyomin, A. Y., et al. (2018). Surface modification of machine parts made of iron–carbon alloys operating under conditions of friction and wear. Journal of Friction and Wear, *39*(3), 283–289.
Timofeєva, L. A., Ustenko, O. V., Tsap, O. І., & Voloshina, L. V. (2019). Pіdvishchennya yekspluatatsіinikh pokaznikіv friktsіinikh klinіv shlyakhom formuvannya pokrittіv zі spetsіalnimi vlastivostyami. Zbіrnik naukovikh prats UkrDUZT, *185*, 88–95.
Timofeєva, L. A., Timofeєv, S. S., Voloshina, L. V., & Kolesnik, M. A. (2021). Pіdvishchennya tribologіchnikh vlastivostei poverkhnevogo sharu chavunu za dopomogoyu obroblennya v seredovishchі peregrіtoї pari vodyanogo rozchinu solei. Vіsnik KhNADU, *94*, 123–127.
Yurasov, S. A., Kozlov, L. Ya., & Rozhkova, Ye. V. (1984). Vliyanie strukturi metallicheskoi osnovi na prochnost khromistikh splavov. Metallovedenie i termicheskaya obrabotka metallov (MitOM), *7*, 18–20.
Bunin, K. P., & Taran, Yu. N. (1972). Stroenie chuguna. Metallurgiya.
Grigorovich, V. K. (1970). Elektronnoe stroenie i termodinamika splavov zheleza. Nauka.
Bobro, Yu. G. (1976). Legirovannnie chuguni. Metallurgiya.
Bobro, Yu. G., Tikhonovich, V. I., & Bobro, A. Yu. (1990). Upravlenie strukturoi metallicheskoi matritsi iznosostoikikh chugunov. Protsessi litya, *1*, 31–35.
Garber, M. Ye. (2010). Iznosostoikie belie chuguni: svoistva, struktura, tekhnologiya, ekspluatatsiya. Mashinostroenie.
Bunin, K. P., Malinochka, Ya. N., & Taran, Yu. N. (1969). Osnovi metallografii chuguna. Metallurgiya.
Taran, Yu. N., & Snagovskii, V. M. (1966). Morfologiya evtektiki v Fe–C–Cr splavakh. Metallovedenie i termicheskaya obrabotka metallov, *4*, 27–30.
Yakovlev, A. Yu., & Volchok, I. P. (2007). Materiali dlya izgotovleniya metallicheskikh form. Lite i metallurgiya, *4*, 118–121.
Skoblo, T. S., Popova, Ye. G., & Sidashenko, A. I. (2001). Vliyanie kolichestva i razmera karbidnoi fazi na svoistva tsentrobezhnolitikh valkov s rabochim sloem iz visokokhromistogo chuguna. Liteinoe proizvodstvo, *8*, 7–8.
Rockel, M., & Bender, R. (2008). Heat‐resistant and scaling‐resistant alloys. In Ullmann's Encyclopedia of Industrial Chemistry. Wiley-VCH. https://doi.org/10.1002/9783527610433.chb01273
Svistunova, T. V., Runova, Z. K., & Kireeva, T. S. (1976). Vliyanie sostava na strukturu i svoistva austenitnikh zhelezokhromonikelevikh splavov. Stal, *9*, 851–853.
Nosova, G. I., & Polyakova, N. A. (1980). Nekotorie osobennosti povedeniya zharoprochnikh splavov pri tsiklicheski menyayushchikhsya temperaturakh. Fizika metallov i metallovedenie (FMM), *50*, 818–825.
Svistunova, T. V., Runova, Z. K., & Kireeva, T. S. (1983). Novie splavi na osnove nikelya dlya raboti pri visokikh temperaturakh. Zashchita metallov, *19*(2), 212–219.
Krell, J., Röttger, A., & Theisen, W. (2019). Chromium-nickel-alloys for wear application at elevated temperature. Wear, *432-433*, 102924. https://doi.org/10.1016/j.wear.2019.102924
Svistunova, T. V., Runova, Z. K., & Kireeva, T. S. (1979). Zharoprochnost i fiziko-khimicheskie svoistva mnogokomponentnikh nikelevikh splavov. Stal, *2*, 141–143.
Taran, Yu. M. (Ed.). (1983). Metaloznavstvo і termіchna obrobka іz zastosuvannyam komp’yuternikh tekhnologіi navchannya: navch. posіbnik. ІSDO.
Sims, Ch., & Khagel, V. (1976). Zharoprochnie splavi (Trans.). Metallurgiya.
Sabol, G. P., & Sticker, R. (1969). Microstructure of Nickel-Based Superalloys. Physica Status Solidi, *35*(11), 1085–1089.
Sustaita Torres, I., Haro Rodriguez, S., Guerrero, M., De la Garza Garza, M., Valdes, E., Deschaux-Beaume, F., & Colás, R. (2012). Aging of a cast 35Cr–45Ni heat resistant alloy. Materials Chemistry and Physics, *133*, 1018–1023. https://doi.org/10.1016/j.matchemphys.2012.02.010
Hu, Z., & Yang, Z.-G. (2003). Development and application of high chromium heat-resistant steel. Journal of Iron and Steel Research, *15*, 60–65.
Kutsova, V. Z., Kovzel, M. A., Grebeneva, A. V., & Chernoivanenko, A. A. (2009). Zakonomernosti formirovaniya strukturi chuguna 28Kh32N3F. Metaloznavstvo ta termіchna obrobka metalіv, *4*, 5–13.
Kutsova, V. Z., Kovzel, M. A., Pogrebna, N. Ye., Grebenєva, A. V., & Fedorova, І. P. (2011). Vpliv іzotermіchnogo gartuvannya na vlastivostі bіlogo visokokhromistogo chavunu 28Kh32N3F. Fundamentalnie i prikladnie problemi chernoi metallurgii, *23*, 244–258.
Kutsova, V. Z., Kovzel, M. A., Grebenєva, A. V., & Velichko, O. O. (2012). Vpliv іzotermіchnogo gartuvannya na fazovii sklad bіlogo visokokhromistogo chavunu 28Kh32N3F. Stroitelstvo, materialovedenie, mashinostroenie, *64*, 81–87.
Kutsova, V. Z., Nesterenko, A. M., Kutsov, A. Yu., & Kovzel, M. A. (2002). Fazovii sostav i svoistva visokokhromistikh chugunov. Perspektivnie zadachi inzhenernoi nauki, *4*, 322–335.
Kutsova, V. Z., Kutsov, A. Yu., Kovzel, M. A., & Kravchenko, A. V. (2004). Struktura i svoistva kompozitnikh valkov, poluchennikh metodom EShN. Oborudovanie i tekhnologii termicheskoi obrabotki metallov i splavov, 109–115.
Kutsova, V. Z., Kovzel, M. A., Kravchenko, A. V., & Zhivotovich, A. V. (2005). Struktura i svoistva kompozitnikh valkov. Strategiya kachestva v promishlennosti i obrazovanii, 86–89.
Kutsova, V. Z., Kutsov, A. Yu., Kovzel, M. A., & Kravchenko, G. V. (2006). Struktura ta vlastivostі bіlikh visokokhromistikh chavunіv dlya kompozitnikh valkіv. Metaloznavstvo ta obrobka metalіv, *1*, 42–46.
Kutsova, V. Z., Kutsov, A. Yu., & Kovzel, M. A. (2003). Vliyanie termicheskoi obrabotki na strukturu i svoistva visokokhromistikh belikh chugunov. Oborudovanie i tekhnologii termicheskoi obrabotki metallov i splavov, 61–68.
Kutsova, V. Z., Kutsov, A. Yu., Kovzel, M. A., & Kravchenko, A. V. (2005). Resursosberegayushchie rezhimi termicheskoi obrabotki kompozitnikh valkov, poluchennikh metodom EShN. Teoriya i praktika metallurgii, *6*, 38–42.
Kutsova, V. Z., Markashova, L. I., Kovzel, M. A., & Kravchenko, A. V. (2007). Formirovanie nanostrukturnoi matritsi v visokokhromistikh chugunakh putem termicheskoi obrabotki. Stroitelstvo, materialovedenie, mashinostroenie, *43*, 229–236.
Kutsova, V. Z., Kovzel, M. A., Nesterenko, A. M., & Zhivotovich, A. V. (2008). Struktura i fazovii sostav zharoprochnogo khromonikelevogo splava «nikorim». Stroitelstvo, materialovedenie, mashinostroenie, *45*(3), 44–51.
Kutsova, V. Z., Kovzel, M. A., & Zhivotovich, A. V. (2008). Issledovanie strukturi, fazovogo sostava i svoistv zharoprochnikh khromonikelevikh splavov v litom sostoyanii. Oborudovanie i tekhnologii termicheskoi obrabotki metallov i splavov, *1*, 23–28.
Kutsova, V. Z., Zhivotovich, A. V., Kovzel, M. A., & Kravchenko, A. V. (2008). Struktura, fazovii sostav i fazovii rentgenospektralnii analiz zharoprochnogo khromonikelevogo splava «nikorim». Metallofizika i noveishie tekhnologii, *30*, 235–243.
Kutsova, V. Z., Kovzel, M. A., & Grebeneva, A. V. (2011). Zakonomernosti formirovaniya strukturi khromonikelevogo splava «nikorim». Novі materіali і tekhnologії v metalurgії ta mashinobuduvannі, *1*, 59–66.
Sokolov, O. G., & Katsov, K. B. (1982). Zhelezomargantsevie splavi. Naukova dumka.
Jellinghaus, W., & Keller, H. (1972). Das System Eisen – Chrom – Kochlenstoff Dievertelungde Chroms Zwishen Ferritund Sondercarbiden. Archiv für das Eisenhüttenwesen, *43*(3), 193–203.
Hattori, S., & Kitagawa, T. (2010). Analysis of cavitation erosion resistance of cast iron and nonferrous metals based on database and comparison with carbon steel data. Wear, *269*(5-6), 443–448. https://doi.org/10.1016/j.wear.2010.04.031
Panov, D., Pertsev, A., Smirnov, A., Khotinov, V., & Simonov, Y. (2019). Metastable Austenitic Steel Structure and Mechanical Properties Evolution in the Process of Cold Radial Forging. Materials, *12*(13), 2058. https://doi.org/10.3390/ma12132058
Malinov, L. S., & Malinov, V. L. (1999). Udarno-abrazivnaya iznosostoikost margantsovistikh stalei s ponizhennim soderzhaniem margantsa. Metallurgicheskaya i gornorudnaya promishlennost, *6*, 39–42.
Popov, V. S., Brikov, N. N., & Dmitrichenko, N. S. (1971). Iznosostoikost pressform ogneupornogo proizvodstva. Metallurgiya.
Silman, G. I., & Dmitrieva, N. V. (2001). Perspektivi ispolzovaniya litikh tverdikh splavov. Materialovedenie i proizvodstvo, *2*, 241–245.
Cheilyakh, A. P., Oleinik, I. M., & Lokshina, Ye. B. (2000). O vliyanii fazovikh prevrashchenii na iznosostoikost splavov s metastabilnim austenitom. Metalli, *1*, 66–71.
Cheilyakh, A. P., Klok, D. V., & Prekrasnii, S. V. (2006). Razrabotka i issledovanie novikh ekonomnolegirovannikh iznosostoikikh chugunov s metastabilnoi strukturoi dlya bistroiznashivayushchikhsya detalei. Metall i lite Ukraini, *9-10*, 13–17.
Mironova, T. M., Nizhnikovskaya, P. F., & Taran, Yu. N. (1981). Karbidnoe prevrashchenie v ledeburite Fe–C–V splavov. In Voprosi formirovaniya metastabilnikh struktur splavov (pp. 132–137).
Chabak, Yu. G., Zurnadzhy, V. I., Golinskyi, M. A., Efremenko, V. G., Zaichuk, N. P., Petryshynets, I., & Shymchuk, S. P. (2022). Current Functional Materials for Wear-Resistant Casting: from Multicomponent Cast Irons to Hybrid High-Boron Alloys. Progress in Physics of Metals, *23*(4), 583–612.
Voitov, V. A. (Ed.). (2008). Osnovi tribologії: Pіdruchnik. KhNTUSG.
Kіndrachuk, M. V., Labunets, V. F., Pashechko, M. І., & Korbut, Є. V. (2009). Tribologіya: pіdruchnik. NAU.
Tikhonovich, V. I., Gavrilyuk, V. P., & Shalevskaya, I. A. (2005). Puti povisheniya abrazivnoi stoikosti khromistikh chugunov. Protsessi litya, *2*, 84–89.
Brykov, M. N., & Efremenko, V. G. (2014). Abrasive Wear Resistance of Steels and Cast Irons (in Russian). https://doi.org/10.13140/2.1.1395.7129
Zakalov, O. V., & Zakalov, І. O. (2011). Osnovi tertya і znoshuvannya v mashinakh: Navchalnii posіbnik. Vidavnitstvo TNTU іm. І.Pulyuya.
Rozhkova, Ye. V., Romanov, O. M., Kozlov, L. Ya., & Romanov, L. M. (1986). Vliyanie metallicheskoi osnovi na iznosostoikost khromistikh chugunov. Metallovedenie i termicheskaya obrabotka metallov, *6*, 30–32.
Bobro, Yu. G. (1976). Legirovannie chuguni. Metallurgiya.
Tikhonovich, V. I., Kovalenko, O. I., & Loktionov, V. A. (1980). Litie iznosostoikie materiali, ikh razrabotka i primenenie. Znanie.
Poddubnii, A. N. (1997). Struktura i svoistva melyushchikh sharov iz legirovannogo belogo chuguna pri lite v kokil. Liteinoe proizvodstvo, *3*, 7–10.
Filipovic, M., & Baiuk, A. (2003). Studies of a wear resistant cast iron. Metalurgija -Sisak then Zagreb-, *9*(4), 259–272.
Pasini, W., Bellé, M. R., Pereira, L., Amaral, R. F., & de Barcellos, V. (2021). Analysis of Carbides in Multi-component Cast Iron Design Based on High Entropy Alloys Concepts. Materials Research, *24*(1), e20200398. https://doi.org/10.1590/1980-5373-mr-2020-0398
Kutsova, V. Z., Kovzel, M. A., Grebeneva, A. V., & Velichko, O. O. (2014). Tribotekhnicheskie svoistva visokokhromistikh splavov v litom i termoobrabotannom sostoyanii pri komnatnoi i povishennoi temperature ispitanii. Metallurgicheskaya i gornorudnaya promishlennost, *3*, 69–74.
Kіndrachuk, M. V., Kutsova, V. Z., Kovzel, M. A., & Tіsov, O. V. (2016). Suchasnі funktsіonalnі materіali z beinіtnoyu nanostrukturnoyu matritseyu ta pіdvishchenimi tribologіchnimi vlastivostyami. Problemi tertya ta znoshuvannya, *70*(1), 112–130.
Druyan, V. M., Gulyaєv, Yu. G., & Chukmasov, S. O. (2000). Teorіya ta tekhnologіya trubnogo virobnitstva: pіdruchnik. Nats. metalurg. akad. Ukraїni, Dnіpro-VAL.
Mazur, V. L., & Timoshenko, V. I. (2018). Teoriya i tekhnologiya prokatki : gidrodinamicheskie effekti smazki i mikrorelef poverkhnosti. ADEF-Ukraina.
Cheilyakh, A. P., Oleinik, I. M., Lokshina, Ye. B., & Lukyanskova, A. N. (1995). Iznosostoikie chuguni s metastabilnim austenitom. Metall i lite Ukraini, *1*, 30–35.
Cheilyakh, A. P. (2009). Ekonomnolegirovannie metastabilnie splavi i uprochnyayushchie tekhnologii. PGTU.
Cheilyakh, A. P., Klok, D. V., & Klimanchuk, V. V. (2002). Vliyanie parametrov zakalki na strukturu i svoistva ekonomnolegirovannogo iznosostoikogo chuguna s metastabilnoi strukturoi. Metall i lite Ukraini, *7*, 33–38.
Sadovskii, V. M., Komarov, O. S., & Gertsik, S. N. (1998). Vliyanie soderzhaniya ugleroda i khroma na svoistva visokokhromistogo chuguna. Liteinoe proizvodstvo, *5*, 12–13.
Brikov, M. N., Yefremenko, V. G., & Yefremenko, A. V. (2014). Iznosostoikost stalei i chugunov pri abrazivnom iznashivanii. Grin D. S.
Efremenko, V. G., Shimidzu, K., Cheilyakh, A. P., Kozarevskaya, T. V., Chabak, Yu. G., Khara, K., & Kusumoto, K. (2013). Abrazivnaya iznosostoikost chugunov so sferoidalnimi karbidami vanadiya. Trenie i iznos, *34*(6), 610–620.
Cheilyakh, A. P., & Oleinik, I. M. (1995). Vliyanie otpuska na strukturu i svoistva khromomargantsovistikh i margantsovistikh chugunov s metastabilnim austenitom. Vestnik Priazovskogo gos. tekhn. universiteta, *1*, 103–108.
Skoblo, T. S., Vishnyakova, Ye. N., & Mozharova, N. M. (1990). Povishenie kachestva prokatnikh valkov iz visokokhromistogo chuguna visokotemperaturnoi termicheskoi obrabotkoi. Metallovedenie i termicheskaya obrabotka metallov (MiTOM), *10*, 7–9.
Cheilyakh, A. P. (2002). Vozmozhnosti sozdaniya metastabilnikh sostoyanii austenita v splavakh na osnove zheleza. Novі materіali і tekhnologії v metalurgії ta mashinobuduvannі, *2*, 31–34.
Cheilyakh, A. P., Oleinik, I. M., Lokshina, Ye. B., & Telitsya, A. V. (2000). O vliyanii fazovikh prevrashchenii na iznosostoikost splavov s metastabilnim austenitom. Metalli, *1*, 66–71.
Kutsova, V. Z., Kovzel, M. A., & Nosko, O. A. (2008). Legovanі stalі ta splavi z osoblivimi vlastivostyami. NMetAU.
Wilson, F. R., & Harding, R. A. (1984). The X-Ray Study of ADI. BCIRA Journal, *318*, 318–331.
Dvoruk, V. І., & Matrosov, M. V. (2008). Pretsizіinii vimіryuvach lіnіinogo znosu mekhanіchnikh tribosistem dlya viprobuvalnoї mashini 2070 SMT-1. Problemi tertya ta znoshuvannya, *50*, 44–49.
Prikhodko, E. V. (1995). Metallokhimiya mnogokomponentnikh sistem. Metallurgiya.
Prikhodko, E. V. (1995). Effektivnost kompleksnogo legirovaniya stali i splavov. Naukova dumka.
Prikhodko, E. V., Togobitskaya, D. N., & Golovko, L. A. (2006). Kontseptualnie osnovi prikladnoi teorii kompleksnogo legirovaniya. Fundamentalnie i prikladnie problemi chernoi metallurgii, *13*, 162–165.
Babachenko, A. I., Togobitskaya, D. N., Kozachek, A. S., Kononenko, A. A., Knish, A. V., & Snigura, I. R. (2016). Optimizatsiya khimicheskogo sostava stali dlya zheleznodorozhnikh koles, obespechivayushchego stabilizatsiyu mekhanicheskikh i povishenie ekspluatatsionnikh svoistv. Metallurgicheskaya i gornorudnaya promishlennost, *2*, 67–73.
Togobitskaya, D. N., Piptyuk, V. P., Petrov, A. F., Grekov, E. V., & Mirgorodskaya, A. S. (2019). Prediction of Ferroalloy Properties for Expert Evaluation of the Efficiency of their Use During Addition to Steel in a Ladle Furnace Unit. Metallurgist, *62*(11-12), 1115–1122.
Pіptyuk, V. P., Togobitska, D. M., Bayul, K. V., Logozinskii, І. M., Levіn, B. A., Petrov, O. P., Grekov, S. V., & Andrієvskii, G. O. (2018). Yeksperimentalne doslіdzhennya pіdvishchennya tekhnologіchnostі briketіv ferosilіtsіyu dlya virobnitstva stalі. Suchasnі problemi metalurgії. Naukovі vіstі, *21*(1), 50–55.
Togobitskaya, D. N., Piptyuk, V. P., Petrov, A. F., Grekov, S. V., Snigura, I. R., Likhachev, Yu. M., & Golovko, L. A. (2017). Bazi dannikh i modeli dlya ekspertnoi otsenki effektivnosti ispolzovaniya ferrosplavov pri proizvodstve stali. Fundamentalnie i prikladnie problemi chernoi metallurgii, *31*, 150–165.
A.s. № 70524 Ukraїna. Metodika viboru khіmіchnogo skladu stalі v ramkakh dіapazonіv reglamentovanikh GOSTom, yakii zabezpechuє stabіlіzatsіyu mekhanіchnikh vlastivostei metaloproduktsії na ratsіonalnomu rіvnі. (2017). Zayavl. № 70012 26.12.2016. Reg. 20.02.2017.
Nesterenko, A. M., Kutsova, V. Z., & Kovzel, M. A. (2003). Issledovanie kristallicheskoi strukturi karbidov tipa Me7S3. Metallofizika i noveishie tekhnologii, *1*, 99–106.
Kutsova, V. Z., Zhivotovich, A. V., Kovzel, M. A., & Kravchenko, A. V. (2008). Struktura i fazovii sostav zharoprochnogo khromonikelevogo splava «nikorim». Metallofizika i noveishie tekhnologii, *30*, 235–243.
Kutsova, V. Z., Kovzel, M. A., Grebeneva, A. V., & Myrgorodskaya, A. S. (2012). Structure, Phases and Alloying Elements Distribution of Nikorim (High-Temperature Strength Ni-Cr Alloy) In Its Cast Form. Metallurgical and Mining Industry, *4*(1), 40–44.
Kutsova, V. Z., Kovzel, M. A., Velichko, O. O., & Stradomski, Z. (2013). Structure, Phases and Alloying Elements Distribution of Nikorim (High-Temperature Strength Ni-Cr Alloy) In Its Cast Form. In Metallurgy 2013. New technologies and achievements in metallurgy, material engineering and production engineering. A collective monograph (pp. 99–105). Czestochowa.
Kutsova, V. Z., Kovzel, M. A., & Grebeneva, A. V. (2011). Zakonomernosti formirovaniya strukturi khromonikelevogo splava «nikorim». Novі materіali і tekhnologії v metalurgії ta mashinobuduvannі, *1*, 59–66.
Ostash, O., Polyvoda, S., Titov, A., Balushok, K., Chepil, R., Zlochevska, N., Narivskiy, A., Shinsky, O., Shalevska, I., Kvasnitska, Y., Kaliuzhnyi, P., Kovzel, M., & Kutzova, V. (2023). Structural materials: manufacture, properties, conditions of use: collective monograph. TECHNOLOGY CENTER PC.
Sychkov, A. B., Parusov, E. V., Zavalishin, A. N., & Kozlov, A. V. (2018). Inherent Effect of the Crystal Structure of Continuous Cast Steel Billets On the Formation of Structure of High Carbon Wire Rod In Coils. Journal of Chemical Technology & Metallurgy, *53*(5), 977–985.
Parusov, Ye. V. (2016). Spadkovii vpliv pokaznikіv yakostі bezperervnolitoї zagotovki na strukturoutvorennya visokovugletsevogo buntovogo prokatu. Metaloznavstvo ta obrobka metalіv, *2*, 55–56.
Kutsova, V. Z., Kovzel, M. A., Grebeneva, A. V., Ratnikova, I. V., & Velichko, O. O. (2015). Vliyanie legiruyushchikh elementov na formirovanie strukturi, fazovogo sostava i svoistv khromomargantsevogo chuguna v litom sostoyanii. Metallurgicheskaya i gornorudnaya promishlennost, *294*(3), 45–48.
Kutsova, V. Z., Kovzel, M. A., Grebeneva, A. V., Shvets, P. Yu., Zyska, A., & Koczurkiewicz, B. (2016). Structure and Mechanical Properties of Chrome- Manganese Cast Irons In the Cast State. In New technologies and achievements in metallurgy, material engineering and production engineering. A collective monograph (pp. 147–153). Czestochowa.
Mazur, V. І., Kutsova, V. Z., Nosko, O. A., & Kovzel, M. A. (2015). Splavi na osnovі zalіza: pіdruchnik. U 2 t. (Vol. 1-2). Vidavnitstvo «Polіtekhnіka».
Bodrova, L. G., Kramar, G. M., Kovalchuk, Ya. O., & Koval, І. V. (2023). Tekhnologіya konstruktsіinikh materіalіv ta materіaloznavstvo, rozdіl Materіaloznavstvo: Navchalnii posіbnik. FOP Palyanitsya V.A.
Downloads
Pages
4-41
Published
December 25, 2025
Categories
Copyright (c) 2025 Maksym Kovzel, Oleksandr Babachenko, Daria Togobitska
Details about the available publication format: PDF
PDF
ISBN-13 (15)
978-617-8360-17-7
How to Cite
Kovzel, M., Babachenko, O., & Togobitska, D. (2025). Iron-based chromium-manganese alloys with an increased range of tribological properties. In I. Shalevska (Ed.), MODERN TRENDS IN CONSTRUCTION MATERIALS TECHNOLOGIES (pp. 4–41). Kharkiv: TECHNOLOGY CENTER PC. https://doi.org/10.15587/978-617-8360-17-7.ch1
